A harmonica fence is a type of fence made of steel wire that is zigzaggingly assembled into a harmonica. Making harmonica fences requires appropriate wire forming tools so that the results can be more precise and consistent. Formation of harmonica wire using the bending method. Bending is a job by applying pressure to certain parts so that plastic deformation occurs in the pressurized part. Harmonica wire is often used for daily needs, such as house fences, land area fences, livestock fences (cattle, chickens, and goats). Making harmonica wire still uses manual methods and requires labor, patience and a long time. This research aims to develop an effective and efficient harmonica wire forming tool to increase the productivity of craftsmen. This research uses an experimental approach in the form of tool development which includes the stages of needs analysis, tool design, prototyping, trials, and evaluation. Workload is calculated based on the worker's pulse, production yield is measured based on the length of the harmonica wire produced, and work productivity is calculated based on the ratio between output (production output) and input (workload) multiplied by his working time. The results showed that there was a decrease in workload and a significant increase in production results and work productivity between using the old method manually and using a new way, namely using ergonomic chain wire forming tools. Workload decreased by 10.3%. Production output increased by 59.8%, while labor productivity increased by 78.7%. Therefore, it is recommended that harmonica wire craftsmen use ergonomic harmonica wire forming tools.
| Published in | American Journal of Science, Engineering and Technology (Volume 8, Issue 4) |
| DOI | 10.11648/j.ajset.20230804.13 |
| Page(s) | 194-198 |
| Creative Commons |
This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited. |
| Copyright |
Copyright © The Author(s), 2023. Published by Science Publishing Group |
Harmonica Wire Forming Tool, Ergonomic Work Tool, Craftsman Work Productivity
| [1] | L. Sudiajeng, T. Tarwaka, K. Sutapa, M. Sudana, and M. Yusuf, “Ergonomic tetrapod reduces the MSDs risk and productivity of steel-bar assembly for reinforcement concrete beams,” Int. Res. J. Eng. IT Sci. Res., vol. 9, no. 1, pp. 1–13, Dec. 2022. |
| [2] | I. G. Santosa, M. Yusuf, I. N. Gunung, and I. K. Rimpung, “Application of Forging Hammer to Increases Productivity of Balinesse Blacksmith,” vol. 208, no. Icist 2020, pp. 195–199, 2021. |
| [3] | K. H. E. Kroemer and E. Grandjean, Fitting The Task To The Human, Fifth Editione A Textbook Of Occupational Ergonomics. London: CRC Press, 2009. |
| [4] | M. Yusuf, “Design of Jewel Stone Sharpener to Increase Jewel Worker Work Productivity in Bali,” in International Conference on Engineering, Technology, and Industrial Application (ICETIA), 2014, pp. 353–357. |
| [5] | R. S. Bridger, Introduction to Ergonomics, 3rd Edition. London: Taylor & Francis, 2008. |
| [6] | A. Manuaba, “Accelerating OHS-Ergonomics Program By Integrating ’Built-In” Within The Industry’s Economic Development Scheme Is A Must-With Special Attention To Small And Medium Enteprises (SMEs),” in Proceedings the 21st Annual Conference of The Asia Pasific Occupational Safety & Health Organization, 2005. |
| [7] | T. Budiyanto and M. Yusuf, “Improvement of Wok Molding Station Increases Work Comfort and Productivity of the Workers,” Int. J. Psychosoc. Rehabilital., vol. 24, no. 4, pp. 8883–8892, 2020. |
| [8] | A. Manuaba, “Total approach is a must for small and medium enterprises to attain sustainable working conditions and environment, with special reference to Bali, Indonesia,” Ind. Health, vol. 44, no. 1, pp. 22–26, 2006. |
| [9] | E. P. L.. Kasper, “Design of systems for productivity and well being,” J. Appl. Ergon., vol. 45, no. 1, pp. 26–32, 2014. |
| [10] | A. A. N. B. Mulawarman, I. K. G. J. Suarbawa, and M. Yusuf, “Slice Tool Model Design Dynamo Drive Tempeh to Increase Work Productivity of Tempeh Chip Craperers,” On the. J. Appl. Sci. Res., vol. 8, no. 4, pp. 88–92, 2022. |
| [11] | I. K. G. J. Suarbawa, M. Arsawan, M. Yusuf, and I. M. Anom Santiana, “Improvement of environment and work posture through ergonomic approach to increase productivity of balinese kepeng coin workers in Kamasan village Klungkung Bali,” in Journal of Physics: Conference Series, 2018. |
| [12] | M. Yusuf and N. Irwanti, “Implementation of 5S in the Pantry Housekeeping of Hotels to Increase Work Productivity,” in The First International Conference on Economics, Business and Social Humanities (ICONEBS 2020), 2020. |
| [13] | T. Budiyanto, M. Yusuf, and B. P. K. As’ari, “The Relationship Between Noise and Temperature to the Level of Work Fatigue in Workers in the Cutting Section,” Am. J. Sci. Eng. Technol., vol. 8, no. 3, pp. 141–145, 2023. |
| [14] | M. Yusuf, W. D. Lokantara, I. M. A. Santiana, and I. W. Sudiasa, “The Effect of Overtime Work On Family Social Aspects,” in Proceedings of the International Conference on Science and Technology (ICST 2018), 2018, vol. 1, no. 13, pp. 500–503. |
| [15] | I. M. A. Santiana and M. Yusuf, “Design of Arrangement of Working Time to Increase Productivity of the Workers by Using Flat Iron at Garment ‘A,’” Log. J. Ranc. Build and Tech., vol. 20, no. 1, pp. 35–39, 2020. |
| [16] | I. G. B. Susana, “Ergonomic Hybrid Solar Dryer Improves Worker Performance and Quality of Anchovy in Banyubiru Jembrana Village. (Dissertation),” Udayana University, 2014. |
APA Style
Gede Oka Pujihadi, I Komang Rusmariadi, I Putu Sastra Negara, I Ketut Gde Juli Suarbawa, M. Yusuf. (2023). Design of Ergonomic Harmonica Wire Forming Tools to Increase Work Productivity of Harmonica Fence Craftsmen. American Journal of Science, Engineering and Technology, 8(4), 194-198. https://doi.org/10.11648/j.ajset.20230804.13
ACS Style
Gede Oka Pujihadi; I Komang Rusmariadi; I Putu Sastra Negara; I Ketut Gde Juli Suarbawa; M. Yusuf. Design of Ergonomic Harmonica Wire Forming Tools to Increase Work Productivity of Harmonica Fence Craftsmen. Am. J. Sci. Eng. Technol. 2023, 8(4), 194-198. doi: 10.11648/j.ajset.20230804.13
AMA Style
Gede Oka Pujihadi, I Komang Rusmariadi, I Putu Sastra Negara, I Ketut Gde Juli Suarbawa, M. Yusuf. Design of Ergonomic Harmonica Wire Forming Tools to Increase Work Productivity of Harmonica Fence Craftsmen. Am J Sci Eng Technol. 2023;8(4):194-198. doi: 10.11648/j.ajset.20230804.13
Share This Article
Twitter
Linked In
Facebook
Copy
Download@article{10.11648/j.ajset.20230804.13,
author = {Gede Oka Pujihadi and I Komang Rusmariadi and I Putu Sastra Negara and I Ketut Gde Juli Suarbawa and M. Yusuf},
title = {Design of Ergonomic Harmonica Wire Forming Tools to Increase Work Productivity of Harmonica Fence Craftsmen},
journal = {American Journal of Science, Engineering and Technology},
volume = {8},
number = {4},
pages = {194-198},
doi = {10.11648/j.ajset.20230804.13},
url = {https://doi.org/10.11648/j.ajset.20230804.13},
eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ajset.20230804.13},
abstract = {A harmonica fence is a type of fence made of steel wire that is zigzaggingly assembled into a harmonica. Making harmonica fences requires appropriate wire forming tools so that the results can be more precise and consistent. Formation of harmonica wire using the bending method. Bending is a job by applying pressure to certain parts so that plastic deformation occurs in the pressurized part. Harmonica wire is often used for daily needs, such as house fences, land area fences, livestock fences (cattle, chickens, and goats). Making harmonica wire still uses manual methods and requires labor, patience and a long time. This research aims to develop an effective and efficient harmonica wire forming tool to increase the productivity of craftsmen. This research uses an experimental approach in the form of tool development which includes the stages of needs analysis, tool design, prototyping, trials, and evaluation. Workload is calculated based on the worker's pulse, production yield is measured based on the length of the harmonica wire produced, and work productivity is calculated based on the ratio between output (production output) and input (workload) multiplied by his working time. The results showed that there was a decrease in workload and a significant increase in production results and work productivity between using the old method manually and using a new way, namely using ergonomic chain wire forming tools. Workload decreased by 10.3%. Production output increased by 59.8%, while labor productivity increased by 78.7%. Therefore, it is recommended that harmonica wire craftsmen use ergonomic harmonica wire forming tools.
},
year = {2023}
}
TY - JOUR T1 - Design of Ergonomic Harmonica Wire Forming Tools to Increase Work Productivity of Harmonica Fence Craftsmen AU - Gede Oka Pujihadi AU - I Komang Rusmariadi AU - I Putu Sastra Negara AU - I Ketut Gde Juli Suarbawa AU - M. Yusuf Y1 - 2023/10/31 PY - 2023 N1 - https://doi.org/10.11648/j.ajset.20230804.13 DO - 10.11648/j.ajset.20230804.13 T2 - American Journal of Science, Engineering and Technology JF - American Journal of Science, Engineering and Technology JO - American Journal of Science, Engineering and Technology SP - 194 EP - 198 PB - Science Publishing Group SN - 2578-8353 UR - https://doi.org/10.11648/j.ajset.20230804.13 AB - A harmonica fence is a type of fence made of steel wire that is zigzaggingly assembled into a harmonica. Making harmonica fences requires appropriate wire forming tools so that the results can be more precise and consistent. Formation of harmonica wire using the bending method. Bending is a job by applying pressure to certain parts so that plastic deformation occurs in the pressurized part. Harmonica wire is often used for daily needs, such as house fences, land area fences, livestock fences (cattle, chickens, and goats). Making harmonica wire still uses manual methods and requires labor, patience and a long time. This research aims to develop an effective and efficient harmonica wire forming tool to increase the productivity of craftsmen. This research uses an experimental approach in the form of tool development which includes the stages of needs analysis, tool design, prototyping, trials, and evaluation. Workload is calculated based on the worker's pulse, production yield is measured based on the length of the harmonica wire produced, and work productivity is calculated based on the ratio between output (production output) and input (workload) multiplied by his working time. The results showed that there was a decrease in workload and a significant increase in production results and work productivity between using the old method manually and using a new way, namely using ergonomic chain wire forming tools. Workload decreased by 10.3%. Production output increased by 59.8%, while labor productivity increased by 78.7%. Therefore, it is recommended that harmonica wire craftsmen use ergonomic harmonica wire forming tools. VL - 8 IS - 4 ER -
Email: